Model Test and Consolidation Analysis of Failure of a Loose Sandy Embankment Dam During Seepage

Failures of earth dam embankments and river dikes, which are constructed of sandy soils with low dry densities, have been observed to occur during rising of water levels. In this paper, a large-scale physical model test was conducted in order to investigate the behavior of a small dam embankment as water levels rose. The test results were simulated by use of a consolidation analysis method coupled with an elastoplastic model for unsaturated soils. All parameters used in the simulation were obtained from element tests; oedometer, triaxial compression, soil water retention, and permeability tests. First, in order to verify the parameters identified, direct shear tests were simulated using the consolidation analysis method; results of the simulation and the tests were consistent. From the embankment model test it was found that the crest of the embankment moved upstream at the first stage of impounding and then moved back. After a seepage surface appeared on the downstream slope, tension cracks occurred on the downstream slope, and sliding occurred through the crack and the downstream toe. The results of the simulation were consistent with those of the model test. This consolidation analysis method could be used to simulate the complex deformations induced by saturation collapse and shear strains and even failure behavior. Old embankments constructed with loose densities might have histories in which cracks occurred on the downstream slopes when the reservoir water level rose, and their stabilities might have decreased.     

Chemical speciation of chlorine in particulate matter by wavelength-dispersive PIXE technique

Chemical speciation of chlorine (Cl) in atmospheric particulate matter (APM) was performed by using a wavelength-dispersive PIXE spectrograph based on high-resolution measurement of Cl-Kβ emission. Samples of atmospheric particles were size-fractioned and collected by a cascade impactor at an urban area in Tokyo. The target position with respect to the spectrograph was precisely adjusted by a 2D laser displacement sensor to achieve high detection efficiency. The samples were irradiated with 2 MeV protons from a tandem electrostatic accelerator. The beam current was 300-500 nA. During the irradiation, the target was cooled by liquid nitrogen to avoid the evaporation of volatile Cl compounds. The measured spectra for the NaCl standard samples clearly showed the Cl-Kβ series composed of the Kβ₁ and the satellite Kβ_x, Kβ₅ lines. From the measured X-ray yields, it was found that the chemical speciation of samples with Cl concentrations as low as ≈1% is possible by this method. The Cl-Kβ series were also successfully observed in the case of APM samples with particle sizes of 11.0-2.1 μm. The spectra shapes of the NaCl standard samples and an APM sample were slightly different from each other, because of some possible mixing of non-sea salt component in the APM sample.     

Hydrogen and carbon dioxide adsorption with tetra‐n‐butyl ammonium semi‐clathrate hydrates for gas separations

Gas adsorption rates of H₂, CO₂, and H₂‐CO₂ gas mixture (H₂/CO₂ = 3.4) with tetra‐n‐butyl ammonium salt (bromide, chloride, and fluoride) semi‐clathrate hydrate particles were measured at 269 K to assess their properties for gas separation. Equilibrium gas occupancies in the S‐cages of the particles were in order of (high to low) for hexagonal structure‐I, tetragonal structure‐I, and superlattice of cubic structure‐I structures with the maximum fractional occupancy by CO₂ being about 40%. The CO₂ diffusion rate depended on the anion size of the salt, which is attributed to distortion of the S‐cage that is close to the molecular size of CO₂. Simulations of semi‐clathrate hydrate particles with theory showed that H₂/CO₂ selectivities could be as high as 36 (3.0 mol% TBAF) and that selectivities for an ideal membrane (3.3 mol% TBAF) could be >100 (269 K, 0.3–4.5 MPa). Semi‐clathrate hydrates have wide application as separation media for gas mixtures. © 2014 American Institute of Chemical Engineers AIChE J, 61: 992–1003, 2015     

Production of d-glucose from pseudo paper sludge with hydrothermal treatment

To convert cellulosic organics contained in industrial paper sludge into glucose, reaction of pseudo paper sludge composed of cellulose and inorganic compounds (calcium carbonate (CaCO₃), talc (Mg₃(Si₄O₁₀)(OH)₂), kaolin (Al₂(Si₂O₅)(OH)₄)) under hydrothermal conditions was studied. Significant amounts of glucose (ca. 23%) could be produced from cellulose in the absence of CaCO₃ for reaction in water at 523 K and 12 min reaction time. On the other hand, in the presence of CaCO3, most glucose decomposed over all conditions, whereas the addition of talc and kaolin to the mixtures increased the glucose yield to about 30%. For the case of chemical recycle of paper sludge with hydrothermal treatment to obtain d-glucose, it can be concluded that it is preferable to separate the calcium carbonate from the paper sludge before hydrothermal treatment.     

Lipid components,fatty acid distributions of triacylglycerols and phospholipids in rice brans

Endogenous tocochromanols in extracted lipids from rice brans of the five cultivars were determined by high-performance liquid chromatography, and were investigated in relation to the fatty acid (FA) distribution of triacylglycerols (TAG) and phospholipids (PL). The dominant tocols were α-tocopherol and γ-tocotrienol, followed by α-tocotrienol and with much smaller amounts of γ-tocopherol and δ-tocotrienol. The lipids of these rice brans comprised mainly TAG (80.6–86.0 wt.%), free FA (4.2–9.0 wt.%), and phospholipids (5.5–6.7 wt.%), whilst other components were also detected in minor proportions (0.2–2.1 wt.%). The PL components included phosphatidyl choline (31.8–46.8 wt.%), phosphatidyl ethanolamine (25.0–38.9 wt.%) and phosphatidyl inositol (20.2–23.2 wt.%). Comparison of these different cultivars showed, with a few exceptions, no significant differences (P > 0.05) in FA distribution. FA distribution of TAG among the five cultivars was evident in the rice brans: unsaturated FA were predominantly concentrated at the sn-2 position and saturated FA primarily occupying the sn-1 or sn-3 position. These results suggest that the tocopherol content, lipid component, and FA distribution in rice brans are not dependent on the cultivation areas during the growing season.     

Superhydrophobic/superhydrophilic micropatterning on a carbon nanotube film using a laser plasma-type hyperthermal atom beam facility

Superhydrophobic/superhydrophilic micropatterning on a carbon nanotube (CNT) film has been achieved using a laser plasma-type hyperthermal atom beam facility, which produces a small amount of damage and generates a highly anisotropic beam. Fluorination and oxidation on CNT films by exposure to fluorine-atom and oxygen-atom beams caused superhydrophobic and superhydrophilic surfaces, respectively, while maintaining the as-grown fibrous forms of the CNT films. Micropatterned oxidation on CNT films without using photoresists created superhydrophilic microdots and microchannels.     

Effect of mean stress on fatigue properties of 1800 MPa-class spring steels

Fatigue tests were conducted for 1800 MPa-class spring steels at various stress ratios. For comparison, similar fatigue tests were conducted for conventional steels whose tensile strength was lower than 1200 MPa. The spring steels exhibited fish-eye fractures, and the origins of these fractures were oxide, TiN and the matrix itself. In contrast, the conventional steels never exhibited fish-eye fractures. The fatigue strength of these steels decreased monotonously as the stress ratio increased, when the fatigue strength was evaluated in terms of stress amplitude. However, the fatigue strength degradation was less than that expected from a modified-Goodman line, and the best fit line was obtained by connecting the fatigue limit at zero mean stress to true fracture strength instead of tensile strength. This research also reviewed application of a power low to the stress ratio effect evaluation. In these results, the difference between the spring and conventional steels was negligible.     

Evaluation of the reduction in CO2 emissions by applying Micro‐Grid to home energy supply system

Dispersed generators such as wind power systems, photovoltaic systems, and cogeneration systems are expected to mitigate the environmental burden of energy consumption, and their installation has been promoted recently. Micro‐Grid is focused on as a method to solve some problems in a commercial electric power line when installing a large number of dispersed generators, and some demonstrative research on Micro‐Grid for large‐scale systems is being carried out now. Also, small cogeneration systems for houses, such as gas engines and fuel cells, are expected to improve CO₂ emissions. However, if the power and heat demand of a family are relatively small or are unbalanced, the cogeneration system does not operate effectively. The authors have studied the application of Micro‐Grid for home energy supply, and have developed a control system to solve this problem. The system achieves a reduction of CO₂ emissions and energy costs by sharing electric power and heat among some houses with cogeneration systems. This paper presents an outline of the newly developed system, and in particular describes the effect of the reduction in CO₂ emissions compared with a conventional energy supply method, and the case in which dispersed generators are installed in some houses and operate independently. © 2009 Wiley Periodicals, Inc. Electr Eng Jpn, 170(3): 19–27, 2010; Published online in Wiley InterScience ( www.interscience.wiley.com ). DOI 10.1002/eej.20879